Dish:

The larger the dish, the stronger is the signal you could receive, that is, the less intermittent is the picture. However, the risk of wind disturbance, cost, and space is proportionally higher. There are two bands of microwave signal normally used for TV. C band is the older generation; it requires a huge dish. Ku band is the modern generation, requires a smaller dish. Many pay TV provide you strong signal by aiming at a smaller coverage area, such that a smaller fixed position dish is good enough. For FTA signal, because of broadcaster is aiming at larger coverage area, so you must use a bigger dish than those pay TV. You might found that not all stations on the same satellite are equal. Different transponder on same satellite can give different signal quality. It is very depending on how much power that transponder is transmitting and which coverage area it is pointing to. Satellite is using solar energy. Power is precious in space.

Depending on how far you are away from the equator. We recommend KU-Band or C-Band (not Excess 1.8meter) dishes. This is the biggest dish size, which can be driven by a standard sized rotor. For northern or southern territory, you might need even bigger dish.

The actual size of the dish is very often exaggerated. Many dishes are oval shaped. The dimension given is based on the longest measurement. A round dish with same size rating of oval shape dish has more area. Some manufacturers use the curvature as measurement. The size claim could be boasted by three inches. We found that every 3 inches increment gives significant improvement on performance. Same size dishes made by different manufacturer can give observable differences on reception because of the real size is different. Do not trust the dimension claimed by manufacturer. You must compare it with your own measurement.

The atmosphere can attenuate signal. The shortest route of air traveled is directly under the equator. When you are away from the equator, the signal has to travel a thicker air. When the satellite is located at the same longitude with you, it has the shortest air path to your site. When you point your dish to another satellite, which is further away from your longitude, your air path is longer. The signal attenuation is proportional to the air path. Cloud, rain, and snow can weaken your signal. Wind can cause temporary off alignment of dish. The dish is never too big. You could receive the signal well on new installation. Your dish could be off aligning after some severe weather. This is especially troublesome on small dish because it is touchy on alignment. Our experience shows that weather is not a major factor of poor reception. Dish size plays a more important role.

Rotor:

Besides the dish, you need a good rotor if you want to receive multiple satellites, unless you want to install several dishes. Some rotor has a weak motor. You might have to push it to get moving. USALS compliance is a good feature to select. Theoretically is supposed to use two motors to control the dish. One motor rotate horizontally, and the other vertically. Since the vertical rotation always follows a fixed geometrical pattern. By using a tilted shaft rotor, we can eliminate the vertical motor.

How to install satellite dish

Survey:

All geostationary satellites were installed at a high altitude of 35,800Km above the equator. On northern hemisphere, we must point the dish toward south .On southern hemisphere, it is just the opposite way. At equator, you have to point the dish upward. At northern or southern hemisphere, depending how far you are away from the equator, you have to point the dish at an elevation angle.

Before installation, you have to find out the longitude and latitude of the installation site.

On the chart http://www.lyngsat.com/, find a satellite, which is closest to your longitude as reference to true south.

Site selection:

Select a rigid spot which has a clear vision to south ? with the height as high as possible. No trees or objects in front. Most rooftop is using very thin wood; your dish could off align or even blow away if not properly reinforced. You can use concrete patio slab as support.

Blowing wind on the dish can give extreme load on the rotor. Occasionally the rotor can fail to rotate to the predetermined position. You can switch to a near by satellite and then come back. It is wise to install your dish on a wall facing south, because you can use the wall as shelter. In Northern hemisphere, wind is often blowing from Northwest. Mounting on rooftop and chimney has nuisance wind disturbance. Your dish should be mounted as high as possible. Mounting on ground level is for sure has blockage to reach remote satellite, because the elevation angle on such satellites could be as low as near zero degree.

Rigid dish support is important. Strong wind can cause intermittent signal.

The pole has to be absolutely vertical. Non-vertical pole can make some satellite off align while the others are on target. The weight of the dish itself can also give tolerance.

Tools required:

Electric drill concrete drill bits, spanner, and ladder.

Level. Use this tool to align vertical pole.

Compass. Compass can read roughly the azimuth. It can give you severe error on placing near a dish. It is not needed if you know the direction. The final fine adjustment is done on field strength meter.

Rope. Use it to hoist up the dish. Use the dish support as hoist. The dish is bulky and heavy. Pre-assemble the dish before installation. Do not attempt to carry it on a ladder; you could lose your balance and fall.

Portable TV or professional satellite finder. Amateur satellite finder cannot identify the satellite. It won?ft help even you found one of them. Portable TV is the best and cheapest choice. Most receivers have built in satellite search feature and field strength meter. It can out perform professional satellite finder.

Installation:

Make measurement on highest side of wall. Make sure your disk would not hit the trough. Dill holes to mount the wall mount. Use a small carbide drill bit to make one hole first. Then enlarge the hole to the correct size. Mount the bracket with one screw. Use a chisel to punch a small hole to guide the drill. Drill the rest of the holes. The holes have to be precisely drilled. If you do not follow this procedure, there is a chance of off alignment. You might have damaged the wall.

　

There are two adjustments on elevation angle. One variable adjustment is on the dish. The other fixed setting is provided on the rotor. If you do not intend to receive multiple satellites with motorized dish, you can simplify the installation. Get the latitude of your site and set it on your rotor and fix it permanently. Install your dish; with lose elevation and azimuth alignment screws. Attach receiver and portable TV near the dish.

Alignment:

Before doing alignment, set your receiver to installation mode. Entry data such as satellite's name, longitude of satellite, transponder frequency, symbol rate, your own longitude, and latitude. Make sure the initial transponder frequency is valid. Otherwise, you can never detect the signal. On the control program, rotate your rotor to the azimuth of target satellite, in this example case,Point your dish approximately to that direction. Rotate your dish up and down by hand until you observed some signal. If you cannot find any, rotate the azimuth by half degree and repeat again and again until you find the satellite. Do a channel search to verify your Satellite. Select the weakest transponder on a remote satellite. Peak the signal. Tighten alignment screws.  A strong signal would give more room for off alignment. Do not use a strong signal to peak. Some satellites are installed on a higher orbit by 1 Km. The USALS calculated azimuth could be off by a fraction of a degree. You can deviate the longitude setting to compensate the error.

Adjust focus by pushing LNB in and out. Peak the signal again. Switch to another satellite and check for signal strength, and do channel search again. If your dish is properly aligned to true south or north, you can switch satellites and still under precise alignment.

When microwave enter the atmosphere, it has similar optical property to light passing through glass. The signal trail could be deflected by a small angle. This tolerance is noticeable on bad weather, and could vary day by day.

Behavior of digital TV:

As we have mentioned, the digital receiver is in fact a computer. It inherits all the flaws of a computer. For example, it could crash or hung as a computer does. It requires time to boot up and tune into a station. If you are experiencing a freeze, just unplug and reboot. Turning off and on ,because this computer is not really shutdown. Occasionally, you are unable to tune to a station, because of the computer cannot process the signal correctly. You can tune to another station of the same satellite and go back and forth to wake it. One advantage of digital TV is it does not give snowy picture on weak signal as analogue TV does. You can always get a clear picture even on low signal. But it gives jerk and squares. On sudden lost of signal. The picture will remain there as a stable image. The clarity of picture depends on the symbol rate of the station. In other words, it is the bandwidth of the channel. To make it easier to understand, say, it is equivalent for you to have a 56K dial up line or a high-speed internet line. Some station pay higher price to least a wider bandwidth channel. It also assigns more data bits on parity check for errors, so the quality of picture will be good. Some station will cut cost by leasing a narrow bandwidth channel, so the picture is blurry.

Digital TV is very different from analogue TV you get used too. You can hear or see some noise on weak analogue signal. But on digital signal, you would get nothing on very weak signal. On barely decodable signal level, you would get square on you pictures, and intermittent sound. You cannot use the picture to do alignment as in analogue TV, because the picture will have delay time to show up, which; by that time you might have missed that alignment position.

Because of the dish needs precision alignment before you can receive something. After installation is complete, you still have to calibrate the dish and entry channel data. For beginners, it could take you several weeks of work. It might not worth to do it by yourself. That could be the reason FTA TV is not as popular as pay TV. However, the FTA is in fact more interesting if you are not an aggression movie bug.

Conclusion:

To simplified the installation instruction. Zero the rotor to center position. Point the dish to true south. Select a weak signal. Peak the signal strength on adjusting elevation angle and focus.

Free to air TV programs are very interesting to watch, because you can see different cultures. You used to have to travel to that country to watch their TV programs. With nowadays technology, the whole world is within your reach. There are many cultural, educational, health, news, sport, family, and religion channels. It has very few violence programs. It is suitable for all ages.

One major feature with FTA is religion programs. All religions are teaching people towards good. However, not many of them could tell you the real truth. What is the world? the future looks like? Is there Hell? What would people be after death? Amount all the religion channels I watched, tbn on satellites agila-2, PAS-9, Thaicom-3, nns-95 gave me the best answer.

　

Do-It-Yourself (DIY) Satellite TV Installation

you live in an apartment or condo complex and aren't allowed to mount your dish on a wall or roof, you can mount it inside, or on your balcony, using a stand which can be ordered from your satellite TV dealer.
After installing your satellite TV dish, run the cable through your house walls to the rooms where you have your TVs, then ground your dish, and caulk all the holes you made in your walls.
Hooking up your satellite TV consists of connecting the cable to your satellite TV receivers, then connecting your receiver to the nearest telephone jack. Follow the wiring diagram that came with your satellite TV equipment package.
Now go to your satellite TV provider's signal strength menu on your satellite TV receiver to get the correct azimuth (direction), elevation (angle), and skew (dish rotation) for your location so your can correctly aim your dish.
Using the signal strength menu, a compass, and a friend to monitor the signal strength menu on your TV, point your dish in the right direction and move it slowly up and down until you obtain maximum signal strength. Be patient as this may take awhile.
Finally, you'll need to contact your satellite TV provider to activate your system.